密码抽屉家具家私衣柜指纹抽屉衣橱指纹抽屉

价格：390.00元/台 最小起订量：100 台 供货总量：1000 台 发货期限：自买家付款之日起7天内发货 有效期至：长期有效

指纹抽屉操作说明（产品系列较多，版本升级造成使用略有差异，请致电13390905616免费索取升级）

1、系统初始化   the system initialization

长按红色按键，绿灯闪烁，10秒后有“哗”一声长鸣，表示系统已初始化成功，所有信息全部清空，密码恢复到“1234”。

Press and hold the red button ,the green LED flash by turn ,after 10 seconds ,when you hear one long beep, that prompts that your system initialize successfully.

☆  2、登记用户指纹   Enrollment of The user fingerprints

第一步，点按红色按键。

The first step, press the red button.

第二步，接着会有“哔，哔”两声短鸣，同时采集窗口红灯亮起，提示按（用户的）手指到指纹采集窗口，直到红灯灭后，拿开手指。

The second step ,when you hear “beep  beep” twice short sound ,the fingerprint sensor flash red ,put your finger on the top of the sensor, when the red light turns off.

第三步，接着有“哔—哔—”一声长鸣表示成功登记指纹；若有“哔，哔，哔”三声短鸣红绿灯同时闪烁三下表示失败。

The three step, then you hear a long “beep” you register the fingerprint successfully .If you hear three beeps that mean you register unsuccessfully.

！注意：如果点按红色按键后立即有“哔，哔，哔”三声短鸣，则表示指纹库已满。

Note: if you press the red button you hear three beeps immediately ,that tell you fingerprints memory is full.

☆  3、指纹认证开锁    Fingerprint access to unlock

按一下“Start/开锁”键，指纹采集窗口红灯亮起，放手指到指纹采集窗口，直到红灯灭后，拿开手指。

有“哔——”一声长鸣表示匹配成功，并绿灯亮提示开门；

若红绿灯同时闪烁三下，即匹配失败，系统立即自动关机。

Press the “Start” button ,the fingerprint sensor light red, put your finger which has been registered until the red light turn off, take finger away,

You hear “beep” once long sound, the green LED light ,the safe door is open.

If the red and green LED flash  three time at the same time ,the fingerprint access unsuccessfully.

☆  4、删除用户指纹    Deleting the user fingerprint

长按“红色”键，红绿灯交替闪烁，10秒后有“哗”一声长鸣，表示所有用户指纹信息全部清空。

Press and hold the red button ,the red and green LED flash by turn ,after 10 seconds ,when you hear one long beep, all fingerprints are deleted.

密码部分 Code

☆  1、密码修改  To change the code

长按“1”键约3秒至绿灯亮，松开按键,输入原密码（未设密码时原密码为出厂密码）,点按“Start”键并“嘀”一声确认,输入新密码（1－8位），点按“start”键再输入一次，点按“Start”键后，接着有“哔——”1声长鸣表示成功修改；若有“哔，哔，哔”3声短鸣表示失败。

Press and hold 1 key about 3 seconds until the green LED light and hear a beep ,loose the key ,input the old code ,then press the “Start” button to confirm .Not longer you will hear the two short beeps ,then input the new code (1-8digits),then press the “Start” button to confirm.

Enter the new code again ,press the “Start” button ,you will hear a long beep ,you change the code successfully .if you hear three short beeps  you change the code unsuccessfully.

说明：出厂密码为“1234”

Introduction :the factory code is “1 2 3 4”

☆  2、密码开锁   Use the code to open the door

输入密码，按“Start”键确认，听到"哔"一声长鸣，电机驱动,开锁成功。

Input the code the press the “Start” button ,you hear a long beep .the motor works  open the door successfully.

注意：在操作过程中，当红灯出现常亮时，表示电压低，请更换电池。

Note: when you are in operating process , the red LED lights ,that indicate the voltage is low ,you need change the battery  as soon as possible.